This item has closed 2 buyers bought 4 items
View other items offered by Electro Micro12065

Similar products

R30 shipping
STEPPER MOTOR SHIELD FOR CNC, 3D PRINTER OR ENGRAVER KS0160
R163.69
R30 shipping
Arduino Uno R3 development board
R250
A4988 CNC Stepper Motor Driver Module
R40
R30 shipping
ARDUINO MEGA KIT FOR CNC / 3D PRINTER CONTROL KS0091
R1,735.67

CNC Shield UNO R3 Board 4xA4988 Driver Kit With Heatsink For Arduino Engraver 3D Printer

New
Indicative market price: R664.38
4 were available
R332.19 50% OFF
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item ready to ship within 3 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Buyer Protection How you're covered
Get it now, pay later

Product information

Condition:
New
Location:
South Africa
Customer ratings:
Product code:
1082323
Bob Shop ID:
274511593
CNC Shield UNO R3 Board 4xA4988 Driver Kit With Heatsink For Arduino Engraver 3D Printer

- CNC Shield Board


Version: 3.0
Color: Red
Size(L*W*H): 68 x 53 x 18 mm
Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)

Features:
1. Uses removable A4988 or DRV8825 compatible stepper drivers.
2. The extension board can be used for carving machine, 3 d printer driver expansion board
3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
4. PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
6. Please note that this is an unassembled kit and Basic soldering skills are needed.

- A4988 Stepper Motor Driver

Color: Red
Size(L*W*H): 20 x 15 x 10 mm
Thermal shutdown circuitry: Yes
Crossover-current protection: Yes
Ground fault protection: Yes
Load short-circuit protection: Yes
Compatible logic supply: 3.3V and 5 V
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16

Features:
1. Mix with slow current decay modes.
2. Internal UVLO and Low RDS (On) Output.
3. Automatic current decay mode detection/selection.
4. Synchronous rectification for low power dissipation.
5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver.

- Uno R3 Board

MCU: ATmega328
Clock speed: 16 MHz
USB interface: ATmega16U2
Operating voltage: 5 V
I-I / O pin output current: 40 mA max
3.3 V output current: 150 mA max
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
EEPROM: 1 kB
Static RAM (SRAM): 2 kB
Flash memory: 32 kB
Size(L*W*H): 68 x 53 x 10 mm

Package included:

1 x Uno R3 Board
1 x CNC Shield Board
4 x A4988 Stepper Motor Driver
4 x Heat Sink
1 x USB Cable
1 x 40-Pin Row Needles





 

Customer ratings: 2 ratings

was recieved, all happy
16 Jun 2017
All OK except for the long wait - 45 days
19 Jun 2017